Miele G 6510 Operating Instructions Manual Download Page 54

Page: 54 / 104

Operation

Energy management

To save energy, the dishwasher will

switch off automatically a few minutes

after the last time a button has been

pressed or after the end of a pro‐

gramme.



Press the



button to switch the

dishwasher back on.

The dishwasher will not switch off auto‐

matically if the time of day display has

been activated (see "Settings menu -

Time of day").

The dishwasher will not switch off

whilst a programme or the FlexiTimer

is running or if there is a fault.

At the end of the programme

The programme has finished when



Finished

appears in the display and the

door has opened slightly (if applicable).
If the

Consumption

programmable func‐

tion is switched on, you can now call up

the actual energy and water consump‐

tion of the programme which has just

finished (see "Caring for the environ‐

ment - EcoFeedback consumption indi‐

cator").

The drying fan may continue to run for

a few minutes at the end of the pro‐

gramme.



Open the door fully so that the door

catch rail retracts again.

You can now empty the dishwasher.



If you have deactivated the auto‐

matic door opening function (see

"Settings menu - AutoOpen"), but

would still like to open the door at

the end of the programme, then

make sure that you open the door

fully.
Otherwise steam from the dishwash‐

er could damage the edge of the

worktop because the fan is no longer

running.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands