Miele G 6510 Operating Instructions Manual Download Page 22

Page: 22 / 104

Before using for the first time

Basic settings



Switch the dishwasher on with the



button.

The welcome screen will appear when

the dishwasher is switched on for the

first time.

Language

The display will change automatically to

the screen for setting the language.



Use the



arrow buttons to select

the language you want and also the

country, if appropriate, and confirm

your selection with

To learn about the display, read the

section with the same name.

A tick



will appear next to the lan‐

guage that has been set.

Time of day

The display will then change to the

screen for setting the time.
The time of day needs to be set before

the "FlexiTimer" programme option can

be used.

You can also show the current time of

day in the display.



Use the



arrow buttons to set the

hour and confirm with



Then set the minutes and confirm

with

Keeping the



arrow buttons press‐

ed in will increase or decrease the

time automatically.

The display will then change to the

screen for setting the clock display.



Select whether or not the time of day

should appear in the display and

confirm your selection with



If you have selected

Display

, con‐

firm the message about higher ener‐

gy consumption with

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands