Miele G 6510 Operating Instructions Manual Download Page 71

Page: 71 / 104

Cleaning and care

Cleaning the spray arms

Particles of food can get stuck in the

spray arm jets and bearings. The spray

arms should therefore be inspected and

cleaned regularly (approx. every 4 - 6

months).



Switch the dishwasher off.

Remove the spray arms as follows:



Take out the cutlery tray (if your dish‐

washer is fitted with one).



Push the

top

spray arm upwards to

engage the inner ratchet. Then un‐

screw the spray arm.



Push the

middle

spray arm upwards



to engage the ratchet. Then un‐

screw the spray arm





Remove the lower basket.



Pull the

lower

spray arm firmly up‐

wards to remove it.



Use a pointed object to push food

particles into the spray arm jets.



Rinse thoroughly under running wa‐

ter.



Refit the spray arms and check that

they rotate freely.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands