Miele G 6510 Operating Instructions Manual Download Page 69

Page: 69 / 104

Cleaning and care

Checking the filters in the

wash cabinet

The filter combination in the base of the

wash cabinet retains coarse soil from

the suds solution, preventing it access‐

ing the circulation system and re-enter‐

ing the cabinet through the spray arms.



This dishwasher must not be

used without all the filters in place.

Collection of coarse soil may cause the

filters to clog. The level of soiling and

time it takes before the filters need

cleaning will vary depending on use.
The message

Check filters

will appear in

the display after every 50 programme

cycles (factory default setting).
You can set the interval for this mes‐

sage to appear to between 30 and 60

programme cycles (see "Settings menu

- Check filters").



Check the filter combination.



Clean it if necessary.



Then confirm the message with

The message will go out.

Cleaning the filters



Switch the dishwasher off.



Turn the handle anti-clockwise to re‐

lease the filter combination





Lift the filter combination out of the

dishwasher



. Remove any coarse

particles and rinse the filter well un‐

der running water.

Use a nylon brush if necessary.



During cleaning ensure that

course soil doesn't get into the cir‐

culation system and cause a block‐

age.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands