Miele G 6510 Operating Instructions Manual Download Page 14

Page: 14 / 104

Warning and Safety instructions



There are electrical wires in the water inlet hose. Do not cut the

water inlet hose, even if it is too long.



The integrated Waterproof system offers protection from water

damage, provided the following conditions are met:

– The dishwasher is correctly installed and plumbed in.
– The dishwasher is properly maintained and parts are replaced

where it can be seen that this is necessary.

– The tap has been turned off when the appliance is not used for a

longer period of time (e.g. during holidays).

The Waterproof system will work even if the appliance is switched

off. However, the appliance must remain connected to the electricity

supply.



The water pressure (flow pressure at the connection point) must

be between 30 and 1000 kPa (0.3 and 10 bar).



A damaged appliance could be dangerous. If the dishwasher gets

damaged, switch it off at the mains and call Miele.



The manufacturer's warranty will be invalidated if the appliance is

not repaired by a Miele approved service technician.



Faulty components must only be replaced by genuine Miele spare

parts. The manufacturer can only guarantee the safety of the appli‐

ance when Miele replacement parts are used.



During installation, maintenance and repair work, the appliance

must be disconnected from the mains electricity supply.



If the connection cable is damaged, it must be replaced with a

special cable of the same type (available from Miele) by a Miele au‐

thorised service technician only in order to avoid a hazard.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands