Miele G 6510 Operating Instructions Manual Download Page 82

Page: 82 / 104

Maintenance

Cleaning the water inlet filter

A filter is incorporated in the screw con‐

nection of the valve on the water inlet

hose. The filter must be cleaned when

dirty, otherwise insufficient water flows

into the wash cabinet.



The plastic housing of the water

connection contains an electrical

component.
The housing must not be dipped in

water.

Recommendation

If the mains water contains a large

amount of insoluble substances, we

recommend fitting a large-area filter in

the connection between the tap and the

water inlet hose threaded union. This

filter is available from Miele.

Cleaning the filter:



Disconnect the dishwasher from the

mains supply.

Switch off at the mains socket and

withdraw the plug.



Turn off the tap.



Unscrew the inlet hose.



Carefully remove the washer.



Withdraw the filter using pointed pli‐

ers and rinse clean under running

water.



Replace the filter and washer, making

sure they are sitting correctly.



Reconnect the inlet hose to the tap,

making sure it goes on correctly and

is not cross-threaded.



Turn on the tap.

If water leaks out, the inlet hose may

not be connected securely or it may

have been screwed on at an angle.



Unscrew and reconnect the inlet

hose correctly.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands