Miele G 6510 Operating Instructions Manual Download Page 8

Page: 8 / 104

Guide to the appliance

Display

General

The display is used to select or set the

following:

– the programme
– the FlexiTimer (Delay start)
– the Settings menu

The display can show the following:

– the current time of day
– the stage the programme is at
– the estimated time left for the pro‐

gramme to run

– the energy and water consumption

(EcoFeedback)

– any relevant fault messages and in‐

formation

To save energy, the dishwasher

switches off after a few minutes if you

do not press any buttons during this

time.

To switch the dishwasher back on

again, press the



button.

Settings menu

The Settings menu is used to alter the

dishwasher's electronics to suit differ‐

ent requirements. You access the Set‐

tings menu by pressing a specific but‐

ton combination (see "Settings menu").
The arrows in the display indicate fur‐

ther options. You can use the



ar‐

row buttons underneath the display, as

appropriate, to select these further op‐

tions.
The

button is used to confirm a

message or setting and also to move to

the next menu or another level.
The option which is selected will have a

tick



next to it.

To exit a sub-menu, use the



arrow

buttons to select the

Back 

option in

the display and confirm your selection

with

If you do not press any of the buttons

for several seconds, the display will re‐

turn to the previous level. You may

need to enter your settings again.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands