Miele G 6510 Operating Instructions Manual Download Page 74

Page: 74 / 104

Problem solving guide

Water inlet fault

Problem

Possible cause and remedy

One of the following

messages appears in

the display:



Open stopcock

The tap is turned off.



Turn on the tap fully.



Water intake

Before rectifying the problem, you must:



Switch the dishwasher off with the



button.

Water intake is restricted.



Turn on the tap fully and start the programme

again.



Clean the water inlet filter (see "Maintenance").



The water pressure at the intake is lower than 30

kPa (0.3 bar).

Seek professional advice.

The following message

appears in the display

during the

SolarSave

pro‐

gramme:



Intake temp. low

The intake water has not reached the required tem‐

perature of 45°C (see "Water connection - Connec‐

tion to the water supply").



Start the programme again.



If the fault message appears again, select a differ‐

ent programme.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands