Miele G 6510 Operating Instructions Manual Download Page 50

Page: 50 / 104

Operation

Detergent dosage



Follow the dosage recommended by

the manufacturer on the packaging.



Unless directed otherwise, use one

detergent tab or add 20 to 30 ml de‐

tergent to compartment II, depending

on the level of soiling. With very

heavy soiling you can also add a

small amount of detergent to com‐

partment l.



Tabs may not dissolve completely

when the Quick wash programme (if

available) is used.

Failure to dispense the recommen‐

ded amount of detergent may impair

cleaning results.



Some dishwasher detergents are

strongly alkaline and contain irritant

or corrosive ingredients which can

cause burning in the nose, mouth

and throat if swallowed, or inhibit

breathing.
Avoid inhalation of powder deter‐

gents and do not ingest dishwasher

detergent. Seek medical advice im‐

mediately if detergent has been

swallowed or inhaled.

Keep detergent and other household

agents out of the reach of children at

all times. Keep children away from

the dishwasher when the door is

open. There could still be detergent

residues in the cabinet. Check that

the detergent dispenser is empty at

the completion of a programme. To

avoid the danger of children coming

into contact with the dishwasher de‐

tergent, only add detergent just be‐

fore starting the programme and

close the door, activating the safety

lock (if your dishwasher is fitted with

one).

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands