Miele G 6510 Operating Instructions Manual Download Page 67

Page: 67 / 104

Cleaning and care

Check your dishwasher regularly (ap‐

prox. every 4-6 months). This way

faults and problems can be avoided.



The external surfaces of this ap‐

pliance are all susceptible to

scratching.
Contact with unsuitable cleaning

agents can alter or discolour the ex‐

ternal surfaces.

Cleaning the wash cabinet

The wash cabinet is largely self-clean‐

ing, provided that the correct amount of

detergent is always used.
If, however, there are limescale or

grease deposits in the cabinet, these

can be removed with a special dish‐

washer cleaner (see "Optional accesso‐

ries"). Follow the instructions on the

packaging.
Using mainly low temperature pro‐

grammes (below 50°C), could cause

bacteria and unpleasant odours to build

up in the wash cabinet. To avoid this,

the dishwasher will increase the tem‐

perature in the final rinse of the selected

programme automatically after several

programmes using low temperatures

have been run.



Clean the filters in the wash cabinet

regularly.

Cleaning the door and the door

seal

Mould could build up on the door seal

and the sides of the dishwasher door

as these surfaces are outside the wash

cabinet and are not accessed and

cleaned by the spray arm jets.



Wipe the door seals regularly with a

damp cloth to remove food deposits.



Wipe off any food or drink residues

which may have dripped onto the

sides of the dishwasher door before

closing it.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands