Miele G 6510 Operating Instructions Manual Download Page 15

Page: 15 / 104

Warning and Safety instructions



In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the appliance and

its surroundings in a clean condition at all times. Any damage which

may be caused by cockroaches or other vermin will not be covered

by the warranty.

Correct installation



The dishwasher must be installed and connected in compliance

with the installation instructions.



Be careful when installing the dishwasher. Wear protective

gloves to avoid injury on any sharp metal components.



The dishwasher must be correctly aligned to ensure problem-free

operation.



In order to ensure stability, built-under and integrated dishwash‐

ers must only be installed under a continuous worktop which is se‐

cured to adjacent cabinetry.



If you want to convert your freestanding dishwasher to a built-un‐

der ("U") model, you will need to order the appropriate conversion

kit. If you remove the existing plinth, you must replace it with a U-

model plinth. This is necessary to avoid the risk of injury caused by

protruding metal parts.



The door springs on either side need to be evenly adjusted. They

are correctly adjusted if the half-opened door (approx. 45° door

opening angle) remains in this position when it is released. The door

must not fall down under its own weight.

The appliance may only be used with correctly adjusted door

springs.

Summary of Contents for G 6510









































































































Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands

Miele G 6510, Operating Instructions Manual

Search results

Summary of Contents for G 6510

Reviews:

Related manuals for G 6510

Brands by name

Popular brands