Miele B 1312 Operating Instructions Manual Download Page 8

Page: 8 / 72

During installation, maintenance and repair work, the appliance

must be disconnected from the mains electricity supply.

Do not damage, remove or bypass the safety features, fixtures

and control elements of this appliance.

Any removable outer panels must be fitted in place, and all

moving or electrical parts shielded before it is switched on.

The appliance must not be used in a non-stationary location (e.g.

on a ship).

In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the appliance and
its surroundings clean at all times. Any damage caused by
cockroaches or other vermin will not be covered by the guarantee.

Correct use

Caution. Danger of burning. The steam emitted, the iron sole

plate and the areas surrounding it on the iron and the steamer
jets get very hot.

This appliance is intended for domestic use only and is not to be

used for commercial purposes.

Do not use a pressure washer or hose to clean the appliance.

Only clean the appliance when it has cooled down.

Danger of squashing and trapping your fingers. Do not place

your fingers between moving parts when assembling, dismantling or
adjusting the height of the appliance.

The appliance must be set up on an even surface and may only

be used in a horizontal position.

Warning and Safety instructions

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands