Miele B 1312 Operating Instructions Manual Download Page 6

Page: 6 / 72

Safety with children

Children under 14 years of age must be kept away from the

appliance unless they are constantly supervised.

Children 14 years and older may only use the appliance

unsupervised if they have been shown how to use it in a safe way
and recognise and understand the consequences of incorrect
operation.

Children must not be allowed to clean or maintain the appliance

unsupervised.

Please supervise children in the vicinity of the appliance and do

not let them play with it.

Make sure that children under 14 years of age cannot access the

steam hose or the mains connection cable either during use or
whilst the appliance is cooling down.

Danger of suffocation. Packaging, e.g. plastic wrappings, must

be kept out of the reach of babies and children. Whilst playing,
children could become entangled in packaging or pull it over their
head and suffocate.

Technical safety

Before setting up the appliance, check it for any externally visible

damage. Do not use a damaged appliance. It could be dangerous.

Check the iron for damage. The iron must not be used if it has

been dropped, if there is any visible damage or if it is leaking.

Before connecting the appliance, make sure that the connection

data on the data plate (voltage and frequency) match the mains
electricity supply.
If in any doubt, consult a qualified electrician.

Warning and Safety instructions

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands