Miele B 1312 Operating Instructions Manual Download Page 54 | Manualshive

Page: 54 / 72

background image

^

Attach the appropriate tool in the
cover onto the water filter in the
right-hand socket and remove it.

^

Remove the water filter from the tool.

^

Clean the water filter thoroughly
under running water.

^

Replace the water filter.

When replacing the water filter,
ensure that the filter seal is
underneath.

^

Replace the seal in the right-hand
socket.

^

Replace the cover and tighten the
screw.

^

Replace the water container.

The appliance is ready for use again.

Do not use the appliance if the water
filter is not in place as this will cause
a fault to be indicated. See "Problem
solving guide".

The water filter must be replaced if it is
worn or damaged. Only use genuine
original Miele replacement parts. These
are available from Miele (see back
cover for contact details) or from your
Miele dealer.

Cleaning and care

54

«
...
52
53
54
55
56
...
»

Summary of Contents for B 1312









































































Reviews:

No comments

Related manuals for B 1312

Brand: jbc Pages: 8

Independent Steam C 100 TS

Brand: Braun Pages: 98

CosmoBeauty COHS09

Brand: Cosmopolitan Pages: 2

Brand: Veit Brisay Pages: 27

Brand: Trisa Pages: 37

Brand: Lumme Pages: 10

Brand: Lumme Pages: 10

Brand: Lumme Pages: 12

Brand: Lumme Pages: 35

Brand: IPSO Pages: 21

NZ 322 Auto-Off

Brand: ECG Pages: 92

Brand: Scarlett Pages: 24

Brand: Ivation Pages: 7

Beautural 724EU-0001

Brand: 1byone Pages: 26

Brand: H.Koenig Pages: 62

Brand: Imetec Pages: 54

Brand: Imetec Pages: 62

ECO COMPACT 9256

Brand: Imetec Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands