Miele B 1312 Operating Instructions Manual Download Page 61

Page: 61 / 72

Problem

Possible cause

Remedy

The fan is not running.

No steam is
required.

The fan only runs when the
steam function on the iron is
operated.

The steam is not
ready.

Wait until the

indicator light

signals that steam is ready.

The water container
is empty or missing.

Fill the water container with fresh
tap water and insert it into the
appliance.

The steamer is
connected.

The fan only runs when the iron is
connected.
Connect the iron.

The ironing table is
not clicked into
place on both sides
of the tower.

Click the ironing table into place
on

both

sides of the tower (see

"Assembling").

There is a fault with
the appliance.

Call Miele Service.

Descaling cannot be
started, although the
indicator light

flashing or lit up.

The iron or steamer
is plugged in.

Disconnect the iron or the
steamer from the steam
connection.

The

button was

not pressed for long
enough.

Press the

button for longer.

There is a fault with
the appliance.

Call Miele Service.

Problem solving guide

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands