Miele B 1312 Operating Instructions Manual Download Page 62

Page: 62 / 72

Problem

Possible cause

Remedy

The appliance
switches off during the
descaling process.

The iron or the
steamer was
connected during
the descaling
process.

Disconnect the iron or the
steamer from the steam
connection. Switch the
appliance on again.

The

indicator light is

on constantly.

The water container
or contents have not
been recognised.

Remove the water container, fill
and replace it.

Rinsing or descaling could still
be taking place. Wait until the
process has finished.

Programming of the water
hardness level has not yet been
completed. Complete this
process.

If the indicator light is still on, call
Miele Service.

The

indicator light is

on constantly during
the descaling process.

The water container
or contents have not
been recognised.

Insert the water container again.

Fill the water container with a
little more water and replace it.

If the indicator light is still on, call
Miele Service.

The

indicator light is

on constantly.

The steam
generator has
overheated.

Allow the steam ironing system
to cool down. The steam ironing
system is ready to use again
when the

has gone out.

If the indicator light is still on, call
Miele Service.

Problem solving guide

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands