Miele B 1312 Operating Instructions Manual Download Page 52

Page: 52 / 72

Cleaning the ironing table
cover

If the ironing table cover is soiled, it can
be removed for washing.

Do not operate the appliance

without an ironing table cover.

When removing the ironing table

cover, always ensure the appliance
is switched off and disconnected
from the electricity supply. Wait until
the ironing table has cooled down.

Undo the fastening of the ironing table
cover at the tapered end of the ironing
table.

Remove the cover in the direction of
the tower. The felt underlayer remains
on the ironing table.

Wash and dry the cover in
accordance with the instructions on
the care label.

Put the cover back on from the tower
end first and draw it down towards the
tapered end.

Pull the cover taut using the cord and
ensure that it is secure.

Close the fastening of the cover and
push it into the space at the tip of the
ironing table.

The appliance is ready for use again.

Replacing the ironing table
cover

Do not use the appliance if the ironing
table cover is damaged.

Do not operate the appliance

without an ironing table cover.

The ironing table cover must be
replaced with an original Miele
replacement.

When changing the ironing table

cover, always ensure the appliance
is switched off and disconnected
from the electricity supply.
Wait until the ironing table has
cooled down.

Undo the fastening of the ironing
table cover at the tapered end of the
ironing table.

Remove the cover in the direction of
the tower. The felt underlayer remains
on the ironing table.

Put the new cover on from the tower
end first and draw it down towards
the tapered end.

Pull the cover taut using the cord and
ensure that it is secure.

Close the fastening of the cover and
push it into the space at the tip of the
ironing table.

The appliance is ready for use again.

Cleaning and care

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands