Miele B 1312 Operating Instructions Manual Download Page 66

Page: 66 / 72

Problem

Possible cause

Remedy

The

indicator light

flashes six times and
the

indicator light is

also lit up.

The steam
generator is
contaminated with
water which is too
hard or too salty.

Start the descaling process by
pressing the

button.

In this case the descaling
requirement is not indicated by
the

light (see "Cleaning and

care").

To avoid this problem in the
future, set the water hardness
level at least a stage higher; for
example, if it is set to 4, increase
it to 5 or more (see "Setting the
water hardness level").

There is a fault with
the appliance.

Switch the appliance off and
then back on again.

If the indicator light continues to
flash, call Miele Service.

The

indicator light

flashes seven times
and the

indicator

light is also lit up.

There is a fault with
the appliance.

Switch the appliance off and
then back on again.

If the indicator light continues to
flash, call Miele Service.

Problem solving guide

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands