Miele B 1312 Operating Instructions Manual Download Page 65

Page: 65 / 72

Problem

Possible cause

Remedy

The

indicator light

flashes four times and
the

indicator light is

also lit up.

The empty or
missing water
container is not
recognised by the
appliance.

Switch off the appliance. Fill the
water container with fresh tap
water and replace it. Do not use
distilled water. Switch the
appliance back on again.

The

indicator light is lit up.

When the steam generator cools
down, it empties automatically.
The steam generator is then
automatically refilled so it is
ready to steam again.

The water container
is not inserted
properly causing air
to be sucked in.

The water feed
pump is being
activated but is not
running.

The water filter is
blocked or missing.

Clean and replace the water
filter (see "Cleaning the water
filter").

The water filter is
damaged (e.g.
bent).

Insert a new water filter (see
"Cleaning the water filter").

If the indicator light is still
flashing, call Miele Service.

The

indicator light

flashes five times and
the

indicator light is

also lit up.

There is a fault with
the appliance.

Switch the appliance off and
then back on again.

If the indicator light continues to
flash, call Miele Service.

Problem solving guide

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands