Miele B 1312 Operating Instructions Manual Download Page 64

Page: 64 / 72

Problem

Possible cause

Remedy

When using the steam
button

on the iron,

drops of water or white
deposits escape from
the steam jets.

The temperature
selected on the iron
is too low.

Set the temperature to at least

ßß

(see "Selecting the

temperature for ironing").

The appliance is not
ready to steam and
the iron has not yet
reached the
selected
temperature.

Wait for the

indicator light to

signal that the steam is ready
and the selected iron
temperature has been reached
(see "Selecting the temperature
for ironing").

Condensation has
formed in the steam
hose due to a pause
in ironing.

To avoid wet spots on your
laundry, do not direct the first
burst of steam after a pause onto
the garment.

The

indicator light

flashes once and the

indicator light is also
lit up.

The appliance was
switched off during
the descaling
process or there
was a power cut.

After power has been restored
and the appliance switched on,
wait a moment. The appliance
will resume the descaling
process from the point at which
the power failed or the process
was interrupted.

The

indicator light

flashes twice and the

indicator light is

also lit up.

The descaling
process was not
carried out properly.

Switch the appliance off and
then back on again.

If the indicator light continues to
flash, call Miele Service.

The

indicator light

flashes three times
and the

indicator

light is also lit up.

There is a fault with
the appliance.

Call Miele Service.

Problem solving guide

Summary of Contents for B 1312









































































Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands

Miele B 1312, Operating Instructions Manual

Search results

Summary of Contents for B 1312

Reviews:

Related manuals for B 1312

Brands by name

Popular brands