Miele B 1312 Operating Instructions Manual Download Page 40 | Manualshive

Page: 40 / 72

background image

Automatic rinse

The automatic rinse function clears the steam generator of
mineral deposits from the evaporated water.

After a water throughput of approx. 3 litres, the water from the
steam generator is drained off into the residual water
container when the Fashion Master is next switched on.

The rinsing process lasts for a couple of minutes.
During the rinsing process the indicator lights do not light
up when the steam ironing system is switched on, the iron
does not heat up and no steam is produced.
Water is drained off into the residual water container.
Steam will escape and trickling noises can be heard
during this process.
The steam ironing system can only be used again when
the automatic rinsing process is completed.

Preparing for the rinsing process

^

Set the appliance to its highest working position (see
"Adjusting the height") to allow access for removing the
residual water container.

^

If the

k

indicator light comes on when the appliance is

switched on, fill the water container (see "Filling the water
container").

^

If the

2

indicator light comes on when the appliance is

switched on, empty and replace the residual water
container.

Cleaning and care

40

«
...
38
39
40
41
42
...
»

Summary of Contents for B 1312









































































Reviews:

No comments

Related manuals for B 1312

Brand: UFESA Pages: 56

Infiniti Pro CD106PRP

Brand: Conair Pages: 2

Brand: T-Fal Pages: 49

Brand: Gallet Pages: 32

Brand: Vitek Pages: 24

Brand: Lumme Pages: 11

Brand: Rowenta Pages: 94

Brand: Beper Pages: 24

Brand: Beper Pages: 24

Brand: Beper Pages: 28

Brand: Beper Pages: 44

Brand: Beper Pages: 48

Brand: Linea 2000 Pages: 32

Brand: Linea 2000 Pages: 40

Brand: Linea 2000 Pages: 58

Brand: Hamilton Beach Pages: 11

Brand: SEVERIN Pages: 44

Brand: Team Kalorik Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands