Miele B 1312 Operating Instructions Manual Download Page 46 | Manualshive

Page: 46 / 72

background image

Preparing for the descaling process

The descaling process can only be started when the

k

indicator light flashes red or lights up constantly.

^

Disconnect the steam hose of the iron or the steamer from
the steam connection.

Do not connect the iron or the steamer during descaling.
This would interrupt the descaling process by switching
off the appliance. If it is switched on again without the iron
or steamer attached, the descaling process is continued.

^

Press the On/Off button

s

to switch on the appliance.

The ring around the

s

button lights up yellow.

Cleaning and care

46

«
...
44
45
46
47
48
...
»

Summary of Contents for B 1312









































































Reviews:

No comments

Related manuals for B 1312

SLIDE FILL GO SMARTFILL 21262

Brand: Russell Hobbs Pages: 8

Brand: Clatronic Pages: 50

Brand: Bosch Pages: 16

Brand: Bosch Pages: 90

Brand: Bosch Pages: 97

Brand: Bosch Pages: 104

Brand: Bosch Pages: 107

Brand: Bosch Pages: 120

Brand: Bosch Pages: 132

Brand: Bosch Pages: 104

LISS&CURL HS4210

Brand: TEFAL Pages: 2

Brand: Continental Electric Pages: 8

Brand: Braun Pages: 21

Atlas Ceramic IZ-1104

Brand: izzy Pages: 24

Brand: KYOWA Pages: 3

Brand: Rotel Pages: 22

Brand: Imetec Pages: 54

Brand: Imetec Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands