background image

i

Thank You

for your purchase of one of the finest marine power packages

available. It incorporates numerous design features to assure

operating ease and durability.
With proper care and maintenance, you will thoroughly enjoy

using  this  product  for  many  boating  seasons.  To  ensure

maximum  performance  and  carefree  use,  we  ask  that  you

thoroughly read this manual.
The  Operation,  Maintenance  &  Warranty  Manual  contains

specific instructions for using and maintaining your product.

We suggest that this manual remain with the product for ready

reference whenever you are on the water.
Again, thank you for purchasing one of our Mercury Marine

products. We sincerely hope your boating will be pleasant!

Mercury Racing, 

N7480 County Road "UU" 

Fond du Lac, WI 54935-9585 

7406

Warranty Message

The  product  you  have  purchased  comes  with  a  limited

warranty from Mercury Marine; the terms of the warranty are

set forth in the 

Warranty Information

 section of this manual.

The  warranty  statement  contains  a  description  of  what  is

covered, what is not covered, the duration of coverage, how

to best obtain warranty coverage, important disclaimers and

limitations of damages, and other related information. Please

review this important information.

© 2006 Mercury Marine

HP1200 SCi Dry Sump

90-8M8021159  1206

Summary of Contents for HP1200 SCi Dry Sump











































































































Reviews: