Maschio JUMBO RAPIDO 6000, Use And Maintenance

Page: 74 / 114

cod. F07011381
2
5
1
3 4
fi g.68
QUANTITÀ OLIO
OIL QUANTITY
QUANTITE D’HUILE
ÖLERFORDERLICHE
CANTIDAD DE ACEITE
Nota:
Non superare le quantità d’olio prescritte.
Note:
do not exceed the prescribed quantity of oil.
Nota:
Ne pas dépasser les quantités d’huile préconisées.
Anmerkung
: Nicht mehr Öl als vorgeschrieben verwenden.
Nota:
No superar las cantidades de aceite indicadas.
OIL Q.
ty
( lt. )
CENTRALE / CENTRAL
6000
7000
7
8000
LATERALE / SIDE
6000
7000
7 + 7
8000
TRASMISSIONE / TRANSMISSION
6000 19 + 19
7000 21 + 21
8000 24 + 24
USE AND MAINTENANCE
ENGLISH
74 - EN
5.1 MAINTENANCE PLAN - Summary table
INTERVAL TYPE OF WORK
WHEN THE MACHINE lS NEW
- Grease all parts indicated by transfer ‘GRASE’ of this lea fl et.
- Lubricate all the transmission chains with mineral oil (SAE 80W/90).
- After
the fi rst hours of work check that all the bolts are still tight.
- Carefully check the general condition of the machine after the fi rst 8 hours service.
In particular, after having checked the tines for wear, it is advisable to check that all screws
and bolts are correctly torqued.
EVERY 8 WORKING HOURS
- Grease the cardan shaft cross journals.
- Grease the side adjuster jacks of the rear bar (1
fi g.68).
- Grease the side supports of the rollers.
EVERY 50 WORKING HOURS
-
CHANGE THE OIL IN THE CENTRAL AND SIDE HOUSINGS AFTER THE FIRST 50
HOURS SERVICE.
- Make sure that the machine is standing on a perfectly fl at surface.
- To check the oil level in the central housing of the fi nal drive, unscrew the lower plug (2 fi g.68)
and make sure that the level reaches the lower edge of the plug hole. Top up if necessary.
- To check the level in the side housings, remove the dipstick (3 fi g.68) and make sure that
the oil reaches the level mark. Top up if necessary.
- To check the oil level in the gear reservoir, unscrew the fi ll plug (4 fi g.68) and use the supplied
dipstick to make sure that the level is between the two reference marks.
Top up if necessary.
EVERY 400 WORKING HOURS
- Completely change the oil in the reduction unit by draining the old oil through the drain plug
(2 fi g.68) and pouring fresh oil through the fi ll/level plug. (5 fi g.68)
- Completely change the oil in the gear reservoir by draining the old oil through the plug (see
fi g.2) and pouring fresh oil through the fi ll/level plug (4 fi g.68).
- At this time, it is also advisable to demount and clean the clutch disks (if a cardan shaft with
clutch is used).
EVERY FIVE YEARS
- Replace all the tubes of the hydraulic systems.
REST PERIODS
At the end of the season, or if a long period of rest is foreseen it is advisable to:
1) Wash the equipment thoroughly with water, especially the chemical substance hoppers,
then dry them. Clean the electrical components
only
with a dry cloth.
2) Carefully check for worn or damaged parts and replace then where required.
3) Check the state of wear of the transmission chains and toothed wheels. Replace damaged
or worn out parts, if required. Use solvent to clean the transmission chains, the toothed
wheels and the chain stretchers. Lubricate with mineral oil (SAE 80W/90) when dry.
4) Firmly tighten all screws and bolts.
5) Apply protecting oil to all unpainted parts.
6) Protect the equipment with a (nylon) cover.
7) Then position it stably in a dry place out of the reach of unauthorized people.
It is in the interests of the user to follow these instructions carefully, as when work recommences, he will fi nd the equipment in perfect
condition.