Grove
Published 01-14-2021 Control # 707-01
9-25
TMS9000-2 SERVICE MANUAL
LUBRICATION
9
5.
While in the horizontal position, first retract Tele 4, and
then retract and extend Tele 5 several times to make
sure that grease is properly distributed.
6.
When Tele 5 greasing is complete, retract and lock
Tele 5 to the 0% pinning location.
7.
Raise boom to 70°.
Telescope Section 4 (Tele 4)
1.
Make sure that the Tele cylinder is locked to Tele 4.
2.
Extend and lock Tele 4 to the 100% pinning location.
3.
Extend and lock Tele 3 to the 50% pinning location.
4.
Lower the boom to 0° and perform the following greasing
in this position:
a.
Grease outer sides of Tele 4 in the areas that touch
the front wear pads of Tele 3.
b.
Grease the rear upper wear pads of Tele 4 on both
sides, at the grease fittings (1), (Figure 9-17),
through the openings in Tele 3.
c.
Grease locking pins on both sides (2), (Figure 9-17).
NOTE:
To grease the rear upper wear pads of Tele 4 at the
50% or 92% pinning locations, extend and lock
Tele 4 to these pinning locations and repeat
Step 4b
greasing.
5.
While in the horizontal position, first retract Tele 3, and
then retract and extend Tele 4 several times to make
sure that grease is properly distributed.
6.
When Tele 4 greasing is complete, retract and lock
Tele 4 to the 0% pinning location.
7.
Raise boom to 70°.
Telescope Section 3 (Tele 3)
1.
Make sure that the Tele cylinder is locked to Tele 3.
2.
Extend and lock Tele 3 to the 100% pinning location.
3.
Extend and lock Tele 2 to the 50% pinning location.
4.
Lower the boom to 0° and perform the following greasing
in this position:
a.
Grease outer sides of Tele 3 in the areas that touch
the front wear pads of Tele 2.
b.
Grease the rear upper wear pads of Tele 3 on both
sides, at the grease fittings (1), (Figure 9-17),
through the openings in Tele 2.
c.
Grease locking pins on both sides (2), (Figure 9-17).
NOTE:
To grease the rear upper wear pads of Tele 3 at the
50% or 92% pinning locations, extend and lock
Tele 3 to these pinning locations and repeat
Step 4b
greasing.
5.
While in the horizontal position, first retract Tele 2, and
then retract and extend Tele 3 several times to make
sure that grease is properly distributed.
6.
When Tele 3 greasing is complete, retract and lock
Tele 3 to the 0% pinning locations.
7.
Raise boom to 70°.
Telescope Section 2 (Tele 2)
1.
Make sure that the Tele cylinder is locked to Tele 2.
2.
Extend and lock Tele 2 to the 100% pinning location.
3.
Extend and lock Tele 1 to the 50% pinning location.
4.
Lower the boom to 0° and perform the following greasing
in this position:
a.
Grease outer sides of Tele 2 in the areas that touch
the front wear pads of Tele 1.
b.
Grease the rear upper wear pads of Tele 2 on both
sides, at the grease fittings (1), (Figure 9-17),
through the openings in Tele 1.
c.
Grease locking pins on both sides (2), (Figure 9-17).
NOTE:
To grease the rear upper wear pads of Tele 2 at the
50% or 92% pinning locations, extend and lock
Tele 2 to these pinning locations and repeat
Step 4b
greasing.
5.
While in the horizontal position, first retract Tele 1, and
then retract and extend Tele 2 several times to make
sure that grease is properly distributed.
6.
When Tele 2 greasing is complete, retract and lock
Tele 2 to the 0% pinning location.
7.
Raise boom to 70°.
Telescope Section 1 (Tele 1)
1.
Make sure that the Tele cylinder is locked to Tele 1.
2.
Extend and lock Tele 1 to the 100% pinning location.
2
1
FIGURE 9-17
BOOM SERVICE LOCATIONS –
REAR UPPER WEAR PADS AND LOCKING PINS
9900-33
Fo
r
Reference
Only
