Loop Telecom IP6610 User Manual Download Page 178

Page: 178 / 190

Chapter 21 Appendix A: Operation Commands

155

Command:

>set DS1 frame

Syntax:

set DS1 frame framing_mode

Explanation:

Set DS1 framing type.

Parameters:

framing_mode D4/ESF/ESF&DS1.403

Command:

>set DS1 code

Syntax:

set DS1 code coding_mode

Explanation:

Set DS1 line coding mode.

Parameters:

coding_mode AMI/B8ZS

Command:

>set DS1 lbo

Syntax:

set DS1 lbo setting

Explanation:

Set DS1 line built out.

Parameters:

setting

0dB/-7.5dB/-15dB

Command:

>set DS1 idle_code

Syntax

set DS1 idle_code idle_code

Explanation:

Any DS0 channel, which is not assigned to a WAN port, is an idle channel. An idle code is
transmitted on idle DS0 channels. Users may program the idle channel to any bit pattern
from 00H to FFH.

Parameters:

idle_code 0x00~0xFF

Command:

>set DS1 yel setting

Syntax:

set DS1 yel setting

Explanation:

Enable/disable DS1 YEL function.

Parameters:

setting

on/off

Command:

>set DS1 inband

Syntax:

set DS1 inband setting

Explanation:

Enable/disable DS1 inband loopback code detective function.

Parameters:

setting

on/off

Command:

>set DS1 address

Syntax:

set DS1 address setting

Explanation:

Set DS1 address.

Parameters:

setting

CSU/TE

Command:

>set DS1 primary_clk

Syntax:

set DS1 primary_clk clock_source

Explanation:

Select DS1 primary clock source.

Parameters:

clock_source

line/internal

Command:

>set DS1 secondary_clk

Syntax:

set DS1 secondary_clk clock_source

Explanation:

Select DS1 secondary clock source.

Parameters:

clock_source

line/internal

Summary of Contents for IP6610






























































































































































































Search results

Summary of Contents for IP6610

Reviews:

Related manuals for IP6610

Brands by name

Popular brands

Loop Telecom IP6610, User Manual

Search results

Summary of Contents for IP6610

Reviews:

Related manuals for IP6610

Brands by name

Popular brands