Loop Telecom IP6610 User Manual Download Page 14

Page: 14 / 190

Chapter 1 Product Description

WAN Interface



Single WAN port



E1/FE1, DS1/FDS1 (Integrated CSU/DSU), DTE (V.35/ V.36/ X.21/ RS232/ EIA530/ RS449)

Ethernet Bridge (BR ordering option)

Layer 2 protocol: HDLC, PPP(PAP/CHAP)/BCP, Frame Relay (up to 10 Frame Relay PVCs), Cisco compatible
HDLC

Remote bridge support (padding/ un-padding Ethernet CRC checksum)

User configurable aging time

Up to 16K MAC Table

Cisco ISL packet transparent

VLAN packet transparent, maximum frame size 2032 bytes

Bridge with management IP

802.1w Rapid Spanning Tree Protocol

Bridge option can be software upgraded to Router (see Layer2, Bridge mode available for transparent bridging)

Support IEEE 802.1q VLAN

Support IEEE 802.1ad Q-in-Q

IP Router (RT ordering option)

Static Route, RIP v1 & v2

Layer 2 protocol: HDLC, PPP(PAP/CHAP)/IPCP, Frame Relay (up to 10 Frame Relay PVCs), Cisco compatible
HDLC

PAP and CHAP

For E1 WAN, In-band management channel on dedicated TS

NAT/NAPT

Port Forwarding: Static/dynamic address/port forwarding table for NAT and NAPT

LAN Interface

One or four Ethernet ports

Embedded Ethernet switch for four Ethernet ports

Conforms to the relevant sections of IEEE 802.3/802.3u

Support SNMP management

Physical interface 10/100 Mbps, Speed auto-sensing, Half/full duplex auto-negotiation, Auto MDI-X

RJ45 connector

DHCP

DHCP server support for LAN users (RFC2131, RFC2132)

BOOTP compatible

SNTP

SNTP client support

Sync with up to 4 time servers

Access Control & Firewall (RT)

Packet filtering based on

Inbound/outbound direction
Source/destination IP address
Protocol types (ICMP, TCP, UDP)
Port number range

Up to 4 control lists

Summary of Contents for IP6610






























































































































































































Search results

Summary of Contents for IP6610

Reviews:

Related manuals for IP6610

Brands by name

Popular brands

Loop Telecom IP6610, User Manual

Search results

Summary of Contents for IP6610

Reviews:

Related manuals for IP6610

Brands by name

Popular brands