Loop Telecom IP6610 User Manual Download Page 147

Page: 147 / 190

Chapter 21 Appendix A: Operation Commands

124

Command:

>del dhcp host option_code

Syntax:

del dhcp host option_code host_name code

Explanation:
Parameters:

host_name

code

Command:

>delete filter

Syntax:

delete filter list_name index

Explanation:

deletes filter entries from a specific list

Parameters:

list_name

name of the list the entry to be deleted from. Either list-1, list-2, list-3,

or list- 4.

index

index of entry to be deleted

Command:

>delete napt forwarding

Syntax:

delete napt forwarding name

Explanation:

deletes the NAPT forwarding entry

Parameters:

name

the name of deleting entry

Command:

>delete nat address

Syntax:

delete nat address index

Explanation:

deletes the NAT public ip address pool

Parameters:

index

the index of the pool to be deleted. The possible value range from 1 to 8.

Command:

>delete nat static

Syntax:

delete nat static public_ip

Explanation:

deletes a static translation entry.

Parameters:

public_ip

the public ip address in the static translation entry to be deleted

Command:

delete rate_limit

Syntax

delete rate_limit policy_num

Explanation:

Deletes the QoS policy index by policy_num from WAN1 policy list.

Parameters:

policy_num policy index number; each policy is index by policy number in the
policy list

Command:

>delete route

Syntax:

delete route net_addr mask

Explanation:

Delete a static route from IP6610’s static routing table.

Parameters:

net_addr

network address of the route entry

mask

subnet mask of the network

Command:

>delete sntp server

Syntax:

delete sntp server index

Explanation:

deletes the specified SNTP server

Parameters:

index

the index number of the server

Command:

>delete svlan

Summary of Contents for IP6610






























































































































































































Search results

Summary of Contents for IP6610

Reviews:

Related manuals for IP6610

Brands by name

Popular brands

Loop Telecom IP6610, User Manual

Search results

Summary of Contents for IP6610

Reviews:

Related manuals for IP6610

Brands by name

Popular brands