LONGHORN LHD8003, Installation Manual

Page: 32 / 33

Table 2: Contact ID Table of Event Codes
CID Code Definition
Operation using keypad without user code, such as arm-away, from disarm to arm-stay
Arm/disarm using master code, by keypad, phone or SMS
Arm/disarm using temporary code, by keypad, phone or SMS
Arm/disarm using the correspondent user code, by keypad, phone or SMS
Arm/disarm by keyfob
Arm/disarm by phone number 1-4 during alarm
Auto arm/disarm
Duress alarm by user 98,with “Disarm” indication on-site
Program with installer code
00
01
02
03
04
05~08
11~16
21~24
30
Appendix 3: Communication Protocol and Codes
Table 1: Contact ID Event Code
Definition
Panic Alarm
Fire Alarm
Duress Alarm
Perimeter Alarm
Active Alarm
Entry/Exit Alarm
Panel anti-tamper alarm or tamper zone alarm
Gas Alarm
AC Power Failure
Low Battery
Reset as Default
Line Loss
Detector Loss
Low Battery for Detector
Arm/Disarm
Arm Stay
Mute Siren
Auto Arm/Disarm Failure
Cancel Alarm
Zone bypass operation, Bypass all or cancel bypass for User 99
Test Report
Enter Programming
Exit Programming
CID Code
100
110
121
131
132
134
137
151
301
302
311
351
381
384
401
406
441
455
521
570
602
627
628
-59- -60-
◆ Detector:
physical methods and output switch signals or wireless signals to the system for disposal, then output
alarm signals, such as infrared detector, smoke detector, etc.
◆ Zone:
An area of the detection range of one or one group detectors.
◆ Bypass:
Close one of the zones temporarily, so that it can not alarm while act in the zone.
◆ Arm Away
The armed status while going out. All the zones without bypass are in armed status.
◆ Arm Stay:
The armed status at night. All the zones are in armed status except active zones.
◆ Disarm
Close the entry/exit zones, active zones, perimeter
◆ 24 hour zone:
No matter armed or disarmed, it is in valid detecting status. It is usually used in fire
alarm, duress alarm and other emergent alarm which can be cancelled only by password holder.
◆ CMS
It is an alarm receiving station, to which the alarm controller sends out alarm information via
telephone line when alarm occurs. The station will take corresponding actions after receiving the alarm.
◆ Entry Delay:
A period for user to enter detection area, activate the delay zone and disarm before the
system alarms. During the period, user can activate several specified zones (entry zone) without alarm
immediately. While exceeding the time, the system alarms if not disarmed. Zones with entry delay are the
exit/entry zone and active zone.
◆ Exit Delay:
A period for user to leave detecting area once the system armed. Zones with exit delay will
not alarm during this period. The zones with exit delay are the exit/entry zone and the active zone.
◆ Supplementary Entry Delay:
The Supplementary Entry Delay is a pre-alarm feature that is
employed in the event that the system is not disarmed during the entry delay.
◆ Panel ID:
ID address can be set for each control panel so that the CMS can identify . Different ID must
be set for different control panels , which is 4-8 digits utmost with default as 1234.
◆ Duress Code:
When user is forced to disarm the control panel by burglar , user inputs duress
password , the control panel is disarmed but sends alarm information to the center stations or receiver . The
duress password can be used to disarm but set parameters .
◆ Chime Zone :
During disarm, while the zone is triggered, the panel will sound “
alarm system! ”
A facility that detects intrusion and abnormal state automatically via some electric or
Welcome to intelligent
zones. Other zones are still in arm status.
:
:
:
Appendix 4: Ter m Definitions