LONGHORN LHD8003, Installation Manual

Page: 21 / 33

To register by code input:
1. Select “ Programming”→ #” → " Device”→ #” → " Zone” → " WL. Register”→ #” “ By Code Input ” .
2. If the code is input before, it will remind if you want to re-register, press “#” to continue , or “ ” to exit .
3. Input the ID, ending with “#”.
4. Press “ ” to quit .
“ “ “ → “ #” →
*
*
This enables you to remove the wireless devices by clearance. For the supervision function. If the device
is removed without clearance, the system will alarm for device loss.
To clear WL:
1. Select “ Programming ” → “#” → “ Device”→ “#” → “ Zone” → “ Clear WL.” → “#”, select “ Clear Single ” or
“ Clear All ”.
2. If “ Clear Single ”, select the zone number ending with “#”. While “ Clear all ” means to clear all enrolled
wireless transmitters .
→ “#”
Clear WL
1. WL Zone 1
Registered!
Save?
Zone ID:
012123
1. WL. Zone1
s
1. By Code Learn
2. WL. Zone 2
3. WL. Zone 3
1.WL. Zone 1
Zone Type
For specific zone type definition, please refer to 6.1.
To set zone type:
1. From the main menu, select “ Programming”→ #” → Device” → Zone”→ #” → Set Zone Type”→ #” .
2. Press the navigation key to select the zone you desire to set ending with “#”, and then select the zone type
for it ending with “ #” to save it .
3. Press “
*
” to exit .
Zone Siren Function
It enables the ser to active or mute external siren for some zone. “ Active ” enables the siren to buzzer during
u
alarm , while “ Mute ” enables the siren dummy . This function is available for Zones No . 1-16( wireless zones ),
21-22( wired zones . Zones ), No . 17 and 1 9 .
To set siren function:
1. From the main menu, select “ Programming”→ “#” → “ Device” → “ Zone”→ “# ” → “ Zone Siren Set”→ “#”.
.
“ “ “ “ “ “ → “#”
→ “#”
2. Use the navigation key to select the zone ending with “#”.
3. Then use navigation key to “ Active ” or “ Mute ” the siren ending with “#”
→ “#”
Keyfob
Register
4. Press “
*
” to exit .
Chime Zone
It is only available for enter/exit zones to enable the “ Welcome Function ”. During disarm , trigger the zone , the
voice of “ Welcome to intelligent alarm system !” will be given off .
To set chime zone:
1. From the main menu, select “ Programming”→ “#” → “ Device” → “ Zone”→ “#” → “ Chime Zone S
et
”→ “#”.
2. Press the navigation key to select the zone NO. ending with “#”.
3. Then press the navigation key to select “ ON ” or “ OFF ” ending with “#”.
4. Press “ ” to exit . *
Keyfob Register
Same as wireless zones, please refer to that.
Clear
Same as wireless zones, please refer to that.
Wireless Siren
Same as wireless zones, please refer to that.
Delete Wireless Siren
Same as wireless zones, please refer to that.
Activate/Mute Siren
It enables the siren(built-in siren, external wired siren or wireless siren) to be on or off.
To activate or mute siren:
1. From the main menu, select “ Programming”→ #” → Device”→ #“ → Siren”→ #” .
2. Press the navigation key to select the siren type: Built-in Siren, Wired Siren, or Wireless Siren ending
with “#”.
3. Then press the navigation key to select “ ON ” or “ OFF ”.
4. Press “
*
” to exit .
Siren Cut-off
Siren cut-off is the period of time the sirens are activated after an alarm has occurred, which can be set
from 0 to 30 minutes.
“ “ “ “ “ ”→ “ Activate/Mute” → “#”
-37- -38-