◆
Service info send to CMS by SMS
ID:1234
Zone: 002 362700002
Event: Service
3627 means the CID exit PROG, 002 means the operator code.
2010/04/10 19:12:17
10.3 GSM Module
●
:
GSM working frequency EGSM900/1800
●
＜
-106
RX sensitivity:
dB
●
Current:
Standby
:
＜
25mA
RX
:
＜
75mA
10.1 Specifications:
Wireless zones 16
●
Wired zones: 2
●
EOL resistance: 2.2K
●
Wireless frequency:
●
433MHZ/868MHZ
Wireless distance:
●
100m(with no obstacle)
≥
PSTN way: DTMF
●
Communication protocol: Contact ID
●
Dimension:250*150*45mm
●
:
Chapter 10: Parameters
●
Power
adaptor
:
Input
100V
-
240VAC
50/60HZ
，
Output
:
12VDC
1.5A
●
Backup
battery
capacity
:
7.2V/1800mAh
●
Working voltage: 12VDC
●
Static current:
＜
90mA@12V(not including wired detectors and GSM
module
)
●
AUX power output: AC10-12V, DC6-8V,
≤
100mA
●
Siren output: ≤400mA
●
PGM output max load: DC 50V/500mA
●
Built-in siren: 85dB
●
Working temperature: -10
℃~+55℃
10.2 Electric Parameters:
Figure -
-
16
AWAY
STAY
DISARM
PROG
-51-
-52-
Trouble
No call for alarm
Telephone can not work normally
as the system is connected into
telephone network
Remote controller can not
operate the system
Wireless zones are out of supervision.
The indicator of power on
keypad does not work
The system has no feedback
when the zone is triggered
False alarm for wireless zones
Abnormal work for PSTN
board using ADSL
During walk test, re-trigger for
detector can not be realized after
1st
trigger
LCD display is abnormal or dirty.
Chapter 11: Troubleshooting
Potential Reasons
User set the incorrect telephone number
User telephone is busy during alarm
Few ringing attempts lead the
system to hang up the phone
automatically
Battery is drained
Enroll remote controller without
programming
Remote controller is too far from the
controller or blocked by obstacles
Wireless detector is not enrolled
The control panel plug is not
inserted in AC socket, or it is
not connected well
The zone is bypassed
When disarm, zone 1,2,3 do not alarm;
arm-stay zone 2 does not alarm
Different wireless zones use the
same code
Only analogue phone line is available.
ADSL means the communication line,
if connect ADSL directly to the control
panel, message transmit will not be realized
There is a sleep period of 5minutes
for detector to save battery between
2 triggers.
Pin connector for LCD is not stable.
Solutions
Set correct telephone number
Set more than two telephone numbers
Increase ringing attempts.
Refer to ringing attempts
adjustment
Replace it with a new battery
Enroll remote controller with
programming
Adjust the distance or angle between
the paner and remote controller
Enroll the detector again
Check the connection of the plug or
replace the socket
Cancel bypass of the zone
Operate normally
Cancel this wireless zone
;
change the
code learn and try again
Connect the phone interface of PSTN board
to phone interface of ADSL segregator. If the
problem still can not be realized, please cha-
nge a high-quality segregator.
Wait 5 minutes after the 1st trigger.
Re-connect the pin connector for LCD
System trouble displays on LCD when standby See 5.6.
System Trouble Query
See 5.6.
System Trouble Query
Summary of Contents for LHD8003
Page 2: ...CREATING SECURITY SOLUTION...
