LONGHORN LHD8003, Installation Manual

Page: 26 / 33

Clear Users
Clear User Codes deletes all programmed user codes and restores the default master and installer
codes and duress codes.
To clear users:
1. From the main menu, select “ Programming ” → “#” → ” Initialization ” → # → “ Clear Users ” “#”.
2. It will display on LCD “ Clear users? ”, press “#” to confirm , or “*” to exit .
Clear Users by Hardware
Clear ing user codes can be also realized by hardware jumper. There is a jumper on the control panel
board “ J3 ”( See Figure 1- Main Board Schematic ). If user codes are forgotten , pls power off , and put the
jumper to “ Default ” and then restart the system , which will reset user codes as default . The “ Default ”
jumper should be cut - off after the system initialization , or else, the action will repeat next power-on.
Reset Zones
This function resets all wireless zones into panic and all wired zones into entry/exit zones.
To reset zones:
1. From the main menu, select “ Programming ” → “ #” → Initialization ” → “ Reset Zone Type ” .
2. It will display on LCD “ Reset Zone Type? ”, press “#” to confirm or “
*
” to exit .
→
→ “ #” → “ #”
Clear Wireless
Clear all wireless includes wireless zones, keyfobs and sirens.
To clear wireless:
1. From the main menu, select “Programming”→“ # ”→“Initialization”→“ # ”→“Clear Wireless”
.
2. It will display on LCD “Clear Wireless?”
,
press “ # ” to confirm or “
*
” to exit
.
→ “#”
6 telephone number and 6 SMS phone number can be set in this system. Regarding telephones,
number 1 and 2 means for CMS and 3-6 means for common phone numbers.
9.1 Telecontrol via Phone
It enables you to remote program the control panel via telephone, such as arm-away, arm-stay, disarm,
repeat alarm voice, and active or mute site siren, etc. You can call the phone number set in the control
panel. After call attempts set, it will hang off with voice guide to input password ending with
“#”: “
For
arm- away, press 1, for arm-stay, press 2, for disarm, press 3, For alarm , press 5, Turn-on site
siren, press 6, turn-off site siren, press 7, for hang up, please press 0
”.
repeat
Chapter 9: Telecontrol via Phone or SMS
Pressing any key during voice play may cause communication error. It
is suggest to operate after voice. If the system is under programming, remote programming is not
available. There should be no voice indication during remote program.
on control panel or phone
Note
-47- -48-
9.2 Dial to Alar m via Panel
The control panel will call the set phone numbers during alarm. You will hear the voice around 5s after pick-
up and will repeat after another 5s, which will last 5 times and then hangs up automatically. After hang up,
if no voice guide, or user can not wait, you can press
“
5
”,
then the panel will issue alarm indication
.
Before it hangs up, you can program by phone.
See following:
Disarm: press
“
3
”.
Arm-away: press
“
3
”
to disarm and then
“
1
”
to arm away
.
Arm-stay: press
“
3
”
to disarm and then
“
2
”
to arm stay
.
Repeat alarm: press
“
5
”
to repeat the alarm
.
Note
:
Alarm is not available to repeat after disarm.
Pressing any key on control panel or phone during voice play may cause communication error. It is
suggest to operate after voice. If the system is under programming, remote programming is not
available. There should be no voice indication during remote program.
Note
Turn off siren: press
“
7
”.
Turn on siren: press
“
6
”
,on-site siren will turn off after 10s
.
Hang up: press
“
0
”
to hang up directly and the system will not dial any phone number
.
Note
9.3 Telecontrol via SMS
It enables you to arm, disarm or query status via SMS. For example, user code is 0808, and control panel
ID is 1234, operate as following:
If program is successful, it means arm or disarm success
;
While program fails
,
means arm or
disarm failure
.
Arm or disarm can not be available during programming. With zone alarm
,
arm can not be realized. There must be no space before or between SMS words.
it