LinMot B1100 Series User Manual Download Page 8

Page: 8 / 91



Motion Control SW

4.3.196 Force Ctrl Change Target Force (382xh)

...........................................................

4.3.197 VAI Go To Pos With Higher Force Ctrl Limit and Target Force (383xh)

..........

4.3.198 VAI Go To Pos With Lower Force Ctrl Limit (384xh)

........................................

4.3.199 VAI Go To Pos With Lower Force Ctrl Limit and Target Force (385xh)

...........

5 SETPOINT GENERATION

...............................................................................................

5.1 VA-I

NTERPOLATOR

.............................................................................................................

5.1.1.1 Parameters and Output

......................................................................................

5.2 P(V)-S

TREAM

....................................................................................................................

5.3 C

OTIONS

....................................................................................................................

5.3.1 Triggered Cam Motions

...........................................................................................

5.3.2 Repeated Cam Motions with the Modulo CamMode

...............................................

5.4 W

INDING

............................................................................................................................

5.4.1 Winding disturbance

................................................................................................

6 COMMAND TABLE

...........................................................................................................

7 DRIVE CONFIGURATION

...............................................................................................

7.1 P

OWER

RIDGE

...................................................................................................................

7.2 X4 I/O D

EFINITIONS

...........................................................................................................

7.2.1 X4.3 Brake

...............................................................................................................

7.2.1.1 X4.3 Brake Operation Enabled Behavior

.........................................................

7.2.1.2 X4.3 Brake Operation /Abort Behavior

............................................................

7.2.1.3 X4.3 Brake Operation Quick Stop Behavior

....................................................

7.2.2 X4.6 Trigger

.............................................................................................................

7.2.2.1 Direct Trigger Mode

.........................................................................................

7.2.2.2 Inhibited Trigger Mode

.....................................................................................

7.2.2.3 Delayed Trigger Mode

......................................................................................

7.2.2.4 Inhibited & Delayed Trigger Mode

..................................................................

7.2.3 X4.8 and X4.9 Limit Switches

..................................................................................

7.2.4 X4.10 and X4.11 PTC 1 and PTC 2

.........................................................................

7.2.5 X4.12 SVE (Safety Voltage Enable)

.........................................................................

7.3 M

ASTER

NCODER

..............................................................................................................

7.4 M

ONITORING

......................................................................................................................

7.4.1 Logic Supply Voltage

...............................................................................................

7.4.2 Motor Supply Voltage

..............................................................................................

7.4.2.1 Phase Switch On Test

.......................................................................................

7.4.3 Regeneration Resistor

..............................................................................................

7.4.4 Temperature Monitoring

.........................................................................................

7.5 P

TRL

TRUCTURE

...........................................................................................................

8 MOTOR CONFIGURATION

............................................................................................

........................................................................

9 STATE MACHINE SETUP

................................................................................................

10 ERROR CODE LIST

........................................................................................................

11 CONTACT ADDRESSES

.................................................................................................

Page 8/91

User Manual Motion Control SW / 06/12/2013

NTI AG / LinMot

Summary of Contents for B1100 Series




























































































Search results

Summary of Contents for B1100 Series

Reviews:

LinMot B1100 Series, User Manual, Page: 8 / 91

Search results

Summary of Contents for B1100 Series

Reviews: