LinMot B1100 Series User Manual Download Page 80

Page: 80 / 91



Motion Control SW

In the Temp Model Parameters section the regeneration resistor’s temperature model is
defined.

Parameter Name

UPID

Description

C Resistor

1026h

Heat capacity of the resistor winding itself.

R Winding
Housing

1027h

Thermal resistance value between resistor winding and its
housing.

C Housing

1028h

Heat capacity of the resistor housing.

R Housing
Environment

1029h

Thermal resistance value between resistor housing and
environment.

Environment
Temperature

102Ah

Environmental temperature of the regeneration resistor.

The figure below shows the implemented temperature model for the regeneration resistor.

7.4.4 Temperature Monitoring

The E1100 drive hardware contains eight absolute temperature sensors for thermal
protection. On the B1100 drive is one sensor placed.

Parameter Name

UPID

Description

Temp Sens Warn
Level

1040h

If the maximal board temperature rises above this level, a
warning is generated (bit 6 in Warn Word is set).

Temp Sens Error
Level

1041h

If the maximal board temperature rises above this level, the
error is generated (error codes 10h..17h).

The table below shows the mapped variables of the temperature monitoring.

Variable Name

UPID

Description

Power Bridge
Temp Ph1+

1BC6h

Temperature of power driver Phase 1+ (E1100 only)

Power Bridge
Temp Ph1-

1BC7h

Temperature of power driver Phase 1- (E1100 only)

Power Bridge
Temp Ph2+

1BC8h

Temperature of power driver Phase 2+ (E1100 only)

Power Bridge
Temp Ph2-

1BC9h

Temperature of power driver Phase 2- (E1100 only)

Power Bridge
Temp Ph2+

1BC9h

Temperature of power driver Phase 2+ (E1100 only)

Page 80/91

User Manual Motion Control SW / 06/12/2013

NTI AG / LinMot

Resistor

Resistor-

Housing

Housing-

Environment

Env

Summary of Contents for B1100 Series




























































































Search results

Summary of Contents for B1100 Series

Reviews:

LinMot B1100 Series, User Manual, Page: 80 / 91

Search results

Summary of Contents for B1100 Series

Reviews: