LinMot B1100 Series User Manual Download Page 5

Page: 5 / 91

Motion Control SW



4.3.56 Modify Curve Data Block 32 Bit Value in RAM (054xh)

......................................

4.3.57 Modify Curve Data Block 64 Bit Value in RAM (055xh)

......................................

4.3.58 Modify Curve Data Block 96 Bit Value in RAM (056xh)

......................................

4.3.59 Setup Encoder Cam On Rising Trigger Event With Delay Counts (069xh)

..........

4.3.60 Setup Encoder Cam On Rising Trigger Event With Delay Counts, Target Pos and
Length (06Axh)

.................................................................................................................

4.3.61 Setup Encoder Cam On Falling Trigger Event With Delay Counts (06Bxh)

........

4.3.62 Setup Encoder Cam On Falling Trigger Event With Delay Counts, Target Pos
and Length (06Cxh)

..........................................................................................................

4.3.63 Setup Encoder Cam On Rising Trigger Event With Delay Counts, Amplitude scale
and Length (06Dxh)

..........................................................................................................

4.3.64 Setup Encoder Cam On Falling Trigger Event With Delay Counts, Amplitude
scale and Length (06Exh)

.................................................................................................

4.3.65 Start VAI Encoder Position Indexing (070xh)

.......................................................

4.3.66 Start Predef VAI Encoder Position Indexing (071xh)

...........................................

4.3.67 Stop Position Indexing and VAI Go To Pos (07Exh)

.............................................

4.3.68 Stop Position Indexing and VAI Go To Pos (07Fxh)

.............................................

4.3.69 VAI 16 Bit Go To Pos (090xh)

..............................................................................

4.3.70 VAI 16 Bit Increment Dem Pos (091xh)

................................................................

4.3.71 VAI 16 Bit Increment Target Pos (092xh)

.............................................................

4.3.72 VAI 16 Bit Go To Pos From Act Pos And Act Vel (093xh)

....................................

4.3.73 VAI 16 Bit Go To Pos From Act Pos Starting With Dem Vel = 0 (094xh)

............

4.3.74 VAI 16 Bit Increment Act Pos (095xh)

..................................................................

4.3.75 VAI 16 Bit Increment Act Pos Starting With Dem Vel = 0 (096xh)

......................

4.3.76 VAI 16 Bit Stop (097xh)

.........................................................................................

4.3.77 VAI 16 Bit Go To Pos After Actual Command (098xh)

.........................................

4.3.78 VAI 16 Bit Go To Pos On Rising Trigger Event (09Axh)

......................................

4.3.79 VAI 16 Bit Increment Target Pos On Rising Trigger Event (09Bxh)

....................

4.3.80 VAI 16 Bit Go To Pos On Falling Trigger Event (09Cxh)

....................................

4.3.81 VAI 16 Bit Increment Target Pos On Falling Trigger Event (09Dxh)

..................

4.3.82 VAI 16 Bit Change Motion Parameters On Positive Position Transition (09Exh)

..........................................................................................................................................

4.3.83 VAI 16 Bit Change Motion Parameters On Negative Position Transition (09Fxh)

..........................................................................................................................................

4.3.84 Predef VAI 16 Bit Go To Pos (0A0xh)

...................................................................

4.3.85 Predef VAI 16 Bit Increment Dem Pos (0A1xh)

....................................................

4.3.86 Predef VAI 16 Bit Increment Target Pos (0A2xh)

.................................................

4.3.87 Predef VAI 16 Bit Go To Pos From Act Pos And Act Vel (0A3xh)

.......................

4.3.88 Predef VAI 16 Bit Go To Pos From Act Pos Starting With Dem Vel = 0 (0A4xh)

..........................................................................................................................................

4.3.89 Predef VAI 16 Bit Stop (0A7xh)

.............................................................................

4.3.90 Predef VAI 16 Bit Go To Pos After Actual Command (0A8xh)

.............................

4.3.91 Predef VAI 16 Bit Go To Pos On Rising Trigger Event (0AAxh)

..........................

4.3.92 Predef VAI 16 Bit Increment Target Pos On Rising Trigger Event (0ABxh)

........

4.3.93 Predef VAI 16 Bit Go To Pos On Falling Trigger Event (0ACxh)

........................

4.3.94 Predef VAI 16 Bit Increment Target Pos On Falling Trigger Event (0ADxh)

......

4.3.95 VAI Predef Acc Go To Pos (0B0xh)

......................................................................

4.3.96 VAI Predef Acc Increment Dem Pos (0B1xh)

.......................................................

4.3.97 VAI Predef Acc Increment Target Pos (0B2xh)

.....................................................

4.3.98 VAI Predef Acc Go To Pos From Act Pos And Act Vel (0B3xh)

...........................

NTI AG / LinMot

User Manual Motion Control SW/ 06/12/2013

Page 5/91

Summary of Contents for B1100 Series




























































































Search results

Summary of Contents for B1100 Series

Reviews:

LinMot B1100 Series, User Manual, Page: 5 / 91

Search results

Summary of Contents for B1100 Series

Reviews: