Linksys LRT214 User Manual Download Page 9 | Manualshive

Page: 9 / 77

background image

5

Getting Started with the Router Configuration

Linksys

Connect/ Disconnect:

If the WAN type is PPPoE or PPTP, this button
will appear . Click Disconnect to cut the
connection from ISP server . Click Connect to
re-dial to the server .

DMZ Status:

NOTE:

It is recommended to designate the configurable port on the
LRT224 as a DMZ port . Go to Device Configuration > Network and
check the Enable DMZ box .

IP Address:

IP address of DMZ port .

DMZ Host:

Private IP of DMZ host .

Firewall Settings

This section displays the current firewall settings:

SPI (Stateful Packet Inspection): Default configuration is On .
DoS (Denial of Service):

Default configuration is On .

Block WAN Request:

Default configuration is On .

Remote Management:

Default configuration is Off .

Access Rule:

The number of access rules configured
in the router .

VPN Settings

Tunnel(s) Used:

Number of tunnels configured .

Tunnel(s) Available: Number of tunnels the router supports .

OpenVPN Status

Tunnel(s) Used:

Number of OpenVPN tunnels configured .

Tunnel(s) Available:

Number of OpenVPN tunnels the router supports .

Log Setting Status

This section displays the following information:

Syslog Server:

Indicates whether Syslog server is activated .

Email Log:

Indicates whether Email Log is activated .

«
...
7
8
9
10
11
...
»

Summary of Contents for LRT214














































































Reviews:

No comments

Related manuals for LRT214

Brand: Panasonic Pages: 44

Brand: Oracle Pages: 24

Brand: IBM Pages: 32

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

IE-SW-VL16-14TX-2SC

Brand: Weidmuller Pages: 17

Brand: IMC Networks Pages: 36

Brand: ZyXEL Communications Pages: 3

Brand: Hama Pages: 25

Brand: Infoblox Pages: 16

24-Port 1000BASE-T

Brand: Comet Labs Pages: 44

Brand: DHD Power Cruiser Pages: 60

Brand: Linksys Pages: 17

Brand: Crestron Pages: 4

DR-4100P Series

Brand: Idis Pages: 97

Brand: D-Link Pages: 16

ProLiant DL100 G2 DPSS

Brand: HP Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands