Linksys LRT214 User Manual Download Page 5 | Manualshive

Page: 5 / 77

background image

1

Hardware Installation

Linksys

1

Hardware Installation

Ports

LRT214

In this chapter we are going to introduce hardware interface as well as
physical installation.

LRT224

•

WAN: The WAN ports can be connected with DSL or cable modems,
provided by your internet service provider (ISP).

•

DMZ: Use the DMZ (Demilitarized Zone) port to connect to a DMZ host,
such as a Web server or mail server. Inbound traffic can access the DMZ
host without exposing your intranet.

•

WAN/DMZ (LRT224):LRT224 Dual WAN Gigabit VPN Router comes with
a port you can configure as a second WAN port or DMZ port based on
your network requirements.

NOTE

Dual WAN settings, such as link failover or load balance, will be
disabled when you configure the port as DMZ port.

LAN (1~4):Use the LAN ports to connect devices such as switching hubs,
computers, printer servers, etc., to the local network or intranet.

«
...
3
4
5
6
7
...
»

Summary of Contents for LRT214














































































Reviews:

No comments

Related manuals for LRT214

Brand: Xantrex Pages: 8

Module NI PXI-8250

Brand: National Instruments Pages: 39

Brand: Watchguard Pages: 24

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: Patton electronics Pages: 9

Brand: Qlogic Pages: 8

Brand: Gira Pages: 6

Enterasys Matrix 2G4082-25

Brand: Enterasys Pages: 58

Brand: Cisco MERAKI Pages: 4

Brand: Conel Pages: 32

DEEP LEARNING PLUS

Brand: Concept Pro Pages: 28

Comet 3356P-LAN

Brand: ZyXEL Communications Pages: 38

Brand: Alcatel-Lucent Pages: 60

Brand: TP-Link Pages: 4

Brand: Xantech Pages: 6

Brand: ZyXEL Communications Pages: 4

3C13755-US - Router 5642

Brand: 3Com Pages: 104

593/25, 593/45, 593/TB, RS-422, RS-485

Brand: Patton electronics Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands