Linksys LRT214 User Manual Download Page 72 | Manualshive

Page: 72 / 77

background image

68

Log

Linksys

Syn Flooding

Heavy syn packet transmission in a short time overloads the
system.

IP Spoofing

Hackers use packet sniffing to intercept data transmitted on
the network. They then change the sender’s IP address to
access the source system.

WinNuke

Servers are attacked or trapped by a trojan program.

Ping of Death

The system fails because the sent data exceeds the maximum
packet that can be handled by the IP protocol.

Unauthorized
Login Attempt

If intruders into the device are identified, the message will
be sent to the system log.

General Log Click to activate the features, including System error message,
blocked regulations, regulation of passage permission, system configuration
change and registration verification.

System Error
Messages

Identifies system errors.

Deny Policies

Records when remote users fail to enter the system because
of access rules.

Allow Policies

Records when remote users enter the system through
successful authentication.

Configuration
Changes

Records changes in the system’s configuration.

A u t h o r i z e d
Login

Records authorized logins.

Four buttons for interaction with the system log online.

View System
Log

Read message content online via the device.

Outgoing Log
Table

View log packets that have been sent out from the PC to
the Internet. Information includes LAN IP, destination IP, and
service port.

Incoming Log
Table

View system packet log of those entering the firewall.
Information includes external source IP addresses,
destination IP addresses, and service ports.

Clear Log

Clears all the current information on the log.

System Statistics

Go to

Configuration > Log > System Statistics

page to view statistics of all router

interfaces.

Click Refresh button to update the statistics.

Interface

Indicates interface: WAN, LAN and DMZ.

Device Name

Port ID: eth0, eth1, eth2, and so on.

Status

Port status: Connected, Disconnected, Enabled, or
Disabled.

IP Address

IP address.

MAC Address

MAC address.

Subnet Mask

Subnet mask.

Default Gateway

Default gateway IP address.

DNS

DNS server.

Received Packets Number of received packets.
Sent Packets

Number of sent packets.

Total Packets

Number of packets sent and received.

Received Bytes

Number of received bytes.

Sent Bytes

Number of sent bytes.

«
...
70
71
72
73
74
...
»

Summary of Contents for LRT214














































































Reviews:

No comments

Related manuals for LRT214

Brand: IBM Pages: 32

Brand: Ubiquiti Pages: 23

Brand: Telex Communications Pages: 28

Brand: E-Lins Pages: 9

Brand: ZyXEL Communications Pages: 2

Brand: Zonet Pages: 53

Brand: IDT Pages: 207

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

Brand: 3Com Pages: 12

Brand: PaloAlto Networks Pages: 28

Brand: OneAccess Pages: 47

Brand: MICRADIGITAL Pages: 2

Brand: Black Box Pages: 62

Brand: ST Pages: 37

P-660R-F1 series

Brand: ZyXEL Communications Pages: 268

Brand: Hama Pages: 45

Meridian 1 Option 11C Mini

Brand: Meridian Pages: 546

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands