Linksys LRT214 User Manual Download Page 52

Page: 52 / 77

VPN

Linksys

Add:

Add a new tunnel and choose Gateway to Gateway or Client
to Gateway..

Group VPN Status

If you enable the Group VPN setting for any of your Client to Gateway tunnels,
the status information appears in this table.

Group Name:

The current Group VPN name.

Connected Tunnels: The number of users logged into the group VPN.
Phase2 Enc/Auth/
Grp:

Settings such as Encryption type (NULL/DES/3DES/
AES-128/AES-192/AES-256), Authentication method
(NULL/MD5/SHA1), and DH Group number (1/2/5)

Local Group:

The IP address and subnet mask of the Local Group.

Remote Client:

The remote clients in the group VPN.

Remote Clients Status: Status of the remote clients: Online or Offline. Click

Detail List to open the Group List window. This
window indicates the Group Name, IP address, and
Connection Time. Click Refresh to update the data, or
click Close to return to the summary page.

Tunnel Test:

Click Connect to verify the tunnel status. The test
result will be updated.

To disconnect, click “Disconnect” to stop the VPN
connection.

Config.:

Setting items include Edit and Delete.

Click on Edit to change the settings. Click the Delete
icon to remove all tunnel settings.

Add:

Click to add a new Group VPN.

VPN Client Status

This section identifies the VPN clients currently connected to the router.

No.:

The ID number of the VPN client.

User Name:

The name of the VPN client.

Status:

The status of the VPN client connection.

Start Time:

Time when the VPN client established its VPN connection to
the router.

End Time:

The time when the VPN client ended its VPN connection to
the router.

Duration:

The period of time that the VPN connection has been active.

Disconnect:

Disconnect the selected VPN client.

Gateway to Gateway

Go to Configuration >VPN > Gateway to Gateway to add a new IPSec tunnel.

The following instructions will guide users to set a VPN tunnel between remote
client and the router.

NOTE:

Remember to click Save to save your settings before leaving the page. You
can also click Cancel to undo the changes.

Add a New Tunnel

Summary of Contents for LRT214














































































Search results

Summary of Contents for LRT214

Reviews:

Related manuals for LRT214

Brands by name

Popular brands

Linksys LRT214, User Manual

Search results

Summary of Contents for LRT214

Reviews:

Related manuals for LRT214

Brands by name

Popular brands