Linksys LRT214 User Manual Download Page 65

Page: 65 / 77

EasyLink VPN

Linksys

Tunnel Test

Click Connect to verify the tunnel status . The test result
will be updated . To disconnect, click Disconnect to stop
the VPN connection .

To delete tunnel settings, select a tunnel, and then click
the Delete icon .

Config

To disconnect, click Disconnect to stop the VPN
connection .

Inbound EasyLink VPN

This page allows the administrator to add a new inbound EasyLink VPN user
(intiator) . The role of the router is responder .

Go to EasyLink VPN > Inbound EasyLink VPN to add a new remote user
configuration .

NOTE:

Click Save before leaving the page or the configuration will be abandoned .
Click Cancel to undo the changes .

NOTE:

To edit an existing inbound Easylink VPN user, go to Easylink VPN summary
page and click the Edit icon of the corresponding VPN user .

Add a New Account

VPN Role

Indicates the role of the router is Responder .

Enable

Indicates whether the specified inbound EasyLink
VPN account is enabled or disabled .

Account Name

The username of remote user .

Password

The user password of remote user .

Authentication Port

Indicates authentication port .

Local Security Group
Type

Local security group type is Subnet .

IP Address

Input LAN IP address of the router .

Subnet Mask

Input subnet mask of the router .

Outbound EasyLink VPN

This page will introduce how to configure outbound EasyLink VPN . The role of
the router is a tunnel initiator .

The router only supports one outbound Easylink VPN connection .

Go to EasyLink VPN > Outbound EasyLink VPN to configure .

NOTE:

Click Save before leaving the page or the configuration will be abandoned .
Click Cancel to undo the changes .

Edit Account

VPN Role

Indicates the role of the router is Initiator .

Enable

Check to enable outbound Easylink VPN connection
or uncheck to disable .

Account Name

Input the username to make an outbound Easylink
VPN connection .

Password

Input the required password to make an outbound
Easylink VPN connection .

Primary Server

Input the IP address of remote server .

Secondary Server

Input the IP address of secondary remote server .

Authentication Port

Select the authentication port .

Keep Alive

Check the box to enable Keep Alive .

Local Security Group
Type

Indicates local security type as Subnet .

IP Address

Input local IP address .

Subnet Mask

Input local subnet mask .

Summary of Contents for LRT214














































































Search results

Summary of Contents for LRT214

Reviews:

Related manuals for LRT214

Brands by name

Popular brands

Linksys LRT214, User Manual

Search results

Summary of Contents for LRT214

Reviews:

Related manuals for LRT214

Brands by name

Popular brands