Lincoln 1997 Town Car Owner'S Manual Download Page 82 | Manualshive

Page: 82 / 305

background image

78

Windshield Washer

To clean the windshield, push in the end of the
wiper knob. For a constant spray, keep the knob
pushed in. After you release the knob, the wipers
operate for two to three cycles before turning off (if
the wipers were OFF) or returning to HI, LO, or
the interval setting selected.

If the washer does not work, check the washer
fluid level and fill it if it is low. See the

Maintenance and Care

chapter. If there is enough

fluid, consult your nearest Ford or Lincoln-Mercury
dealer.

Do not try to clean the windshield when the
washer fluid container is empty or activate the
washers at any time for more than 15 seconds
continuously. This could damage the washer pump
system.

WARNING

Always warm up the windshield with
the defroster before you use the washer
fluid. In freezing weather, the washer
solution may freeze on the windshield
and obscure your vision.

For information about refilling the washer fluid or
replacing your windshield wiper blades, see

Windshield washer fluid and Wipers

in the Index.

Hazard Flasher

The hazard flasher serves as a warning to other
drivers to be careful when approaching or passing
your vehicle.

File:05fncft.ex

Update:Mon Jun 17 13:49:49 1996

«
...
80
81
82
83
84
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

DAF POWERCHOICE 250A

Brand: Paccar Pages: 20

Brand: REVCAMUK Pages: 4

Brand: Cadillac Pages: 34

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: WABCO Pages: 52

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: Warn Pages: 5

Brand: Toyota Pages: 165

Brand: APS Pages: 3

Brand: Prorack Pages: 15

Brand: Pontiac Pages: 20

Brand: TracRac Pages: 8

Charger SRT 392 2017

Brand: Dodge Pages: 576

Brand: Lexus Pages: 108

iTrip Bluetooth

Brand: Griffin Technology Pages: 6

Pajero Pinin 1999

Brand: Mitsubishi Pages: 919

Brand: Porsche Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands