manualshive.com logo in svg

Lincoln 1997 Town Car, Owner'S Manual

The Lincoln 1997 Town Car Owner's Manual, the perfect companion for every proud owner, is available for download, absolutely free! This comprehensive manual provides all the necessary information and guidance to maximize your driving experience in the luxurious Lincoln 1997 Town Car. Download it now from manualshive.com!

Share
Download
background image

114

Replacing the Batteries

The remote entry transmitter is powered by two
coin type three-volt lithium 1616 batteries
(included) that should last for several years of
normal use. If you notice a significant decrease in
operating range, the batteries should be replaced.
Replacement batteries can be purchased at most
pharmacies, watch stores or at your Ford or
Lincoln-Mercury dealer.

NOTE:

The operating range of the remote entry

system can also be affected by weather conditions
(such as very cold temperatures) or structures
around the vehicle (buildings, other vehicles, radio
and TV towers, etc.). Typical operating range will
allow you to be up to 33 feet (10 meters) away
from your vehicle.

The transmitter can be snapped apart to replace the
batteries by twisting a thin coin between the two
halves of the transmitter. DO NOT TAKE THE
FRONT PART OF THE TRANSMITTER APART.

When installing the new batteries, be sure to place
the positive (+) side down as marked. Snap the two
halves back together.

Replacement/additional transmitters

In the event a transmitter is lost, a new one may
be purchased from your dealer. To program the
new transmitter:

Additional transmitters may be purchased from your
dealer (remote entry system will work with up to
four transmitters). To program additional
transmitters to your vehicle, use the following
procedure for replacement transmitters.

1.

Enter the factory keyless entry code. Your
personal code will not allow programming.

2.

Press the 1/2 button.

File:05fncft.ex

Update:Mon Jun 17 13:49:49 1996

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

CAMPARK R10 Manual preview
R10
Brand: CAMPARK Pages: 20
Safe Fleet PRIME DESIGN VCR 326 Assembly Instructions Manual preview
PRIME DESIGN VCR 326
Brand: Safe Fleet Pages: 16
Safe Fleet Prime Design VBC PC11 Quick Start Manual preview
Prime Design VBC PC11
Brand: Safe Fleet Pages: 8
Safe Fleet Prime Design AR1418 Manual preview
Prime Design AR1418
Brand: Safe Fleet Pages: 4
UltraGauge EM Installation & Operation Manual preview
EM
Brand: UltraGauge Pages: 55
Yakima SkyBox 12 Installation Instructions Manual preview
SkyBox 12
Brand: Yakima Pages: 6
Yakima HoldUp Plus2 Manual preview
HoldUp Plus2
Brand: Yakima Pages: 18
Webasto CC4E Installation And Service Instructions Manual preview
CC4E
Brand: Webasto Pages: 34
Actia SmarTach Manual preview
SmarTach
Brand: Actia Pages: 102
Q Mobility Group Q Access Alpha GSE 2023 Installation Manual preview
Q Access Alpha GSE 2023
Brand: Q Mobility Group Pages: 9
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Brand: SAN HIMA Pages: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Brand: Paccar Pages: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Brand: Mercedes-Benz Pages: 153
Ford 2001 Explorer Owner'S Manual preview
2001 Explorer
Brand: Ford Pages: 256
Edelbrock 2917 Nstallation Instructions preview
2917 Nstallation
Brand: Edelbrock Pages: 1
Rugged Ridge 11232.20 Quick Start Manual preview
11232.20
Brand: Rugged Ridge Pages: 2
Edelbrock 29135 Installation Instructions preview
29135
Brand: Edelbrock Pages: 2
Mercedes-Benz 1989 560 SL Owner'S Manual preview
1989 560 SL
Brand: Mercedes-Benz Pages: 93

Brands by name

Popular brands

Load more brands