Lincoln 1997 Town Car Owner'S Manual Download Page 155 | Manualshive

Page: 155 / 305

background image

151

9.

Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 6 through
8.

NOTE:

To remove the retractor from automatic

lock mode, allow seat belt to retract fully to its
stowed position and the retractor will automatically
switch back to the vehicle sensitive locking mode
for normal adult usage.

Installing Child Safety Seats in the Rear

Outboard Seating Positions

Your rear outboard seating positions are equipped
with a cinch tongue on the safety belts. Use the
following procedure for installing a child safety seat
in these locations.

1.

Grasp the belt webbing below the tongue and
pull as much of the belt out of the retractor as
possible. Hold the belt out. See Figure 1.

File:06fnsst.ex

Update:Fri Jun 21 08:57:53 1996

«
...
153
154
155
156
157
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

AUDI 4G HIGHEND

Brand: KAP Pages: 20

Brand: Yakima Pages: 4

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Brand: Phonocar Pages: 6

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: Raytel LLC Pages: 40

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Subaru Pages: 2

Brand: Subaru Pages: 328

Brand: Reese Explore Pages: 9

Brand: ConWys AG Pages: 16

1995 Cutlass Supreme

Brand: Oldsmobile Pages: 340

Brand: Webasto Pages: 23

Brand: Rugged Ridge Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands