Lincoln 1997 Town Car Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 305

background image

31

Overdrive Off Indicator

This light tells you that the Transmission Control
Switch (TCS) has been pushed. When the light is
on, the transmission will not shift into overdrive.
Depressing the button will return the vehicle to
“overdrive on” mode. The transmission will be in
the “overdrive on” mode when the vehicle is
started even if the O/D OFF mode was selected
when the vehicle was last shut off.

If the light does not come ON when the TCS
is depressed or if the light FLASHES when you
are driving, have your vehicle serviced at the
first opportunity. If this condition persists,
damage could occur to the transmission.

Low Washer Fluid Light

This light comes on when there is less than a
quarter of the container of washer fluid left. With
the ignition ON this light will flash five (5) times
and a tone will sound for one (1) second, and then
the light will remain on.

Door Ajar Light

If one of the doors is not completely shut, this light
comes on when you turn the ignition to ON. With
the ignition on this light will flash five (5) times
and sound a tone for one (1) second, and then the
light will remain on.

File:03fnist.ex

Update:Mon Jun 17 13:46:47 1996

«
...
34
35
36
37
38
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: Happy Orange Pages: 2

Brand: Acdeos Pages: 38

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Farad Pages: 8

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: Chariot Carriers Pages: 3

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

Brand: TATA Motors Pages: 236

Brand: Ecco Pages: 12

Brand: Whelen Engineering Company Pages: 9

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Akerstroms Tx700

Brand: LXE Pages: 146

Brand: Unex Pages: 30

Brand: A-Tach Mounts Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands