Lincoln 1997 Town Car Owner'S Manual Download Page 183 | Manualshive

Page: 183 / 305

background image

181

Roadside Emergencies

The flashers work whether your vehicle is running
or not. The flashers work for up to two hours
when the battery is fully charged and in good
condition without draining the battery excessively. If
the flashers run for longer than two hours or if the
battery is not fully charged, the battery can be
drained.

If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision

Fuel Pump Shut-off Switch

If the engine cranks but does not start even after a
small collision, the fuel pump shut-off switch may
have been actuated. The shut-off switch is a device
intended to stop the fuel pump when your vehicle
has been involved in a substantial jolt.

Once the shut-off switch is actuated, you must reset
the switch by hand before you can start your
vehicle. The switch is on the left side of the trunk.

File:10fnert.ex

Update:Thu Jun 20 15:16:36 1996

«
...
181
182
183
184
185
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: ULTIMATE SPEED Pages: 19

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: Camcar Pages: 2

Brand: Ironton Pages: 7

Brand: Metra Electronics Pages: 8

Brand: Volvo Pages: 24

Brand: Jeep Pages: 136

Brand: FALCON RIDGE Pages: 4

Brand: Elinchrom Pages: 101

Brand: Rugged Ridge Pages: 5

Brand: Saab Pages: 288

Brand: Alfa Romeo Pages: 268

Brand: HawksHead Pages: 10

Brand: SMART Pages: 26

Brand: Whelen Engineering Company Pages: 2

Brand: AA Products Pages: 6

Brand: Honda Pages: 441

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands