Lincoln 1997 Town Car Owner'S Manual Download Page 128 | Manualshive

Page: 128 / 305

background image

124

2.

Rotate the thumbwheel from “0” to “1” (the
lowest heat level). Allow five minutes for the
heat level to stabilize.

3.

If the heat level is not high enough for
comfort, select increased heat levels “2”
through “5” (the maximum level). Allow at
least two minutes for the heat level to stabilize
at any new level selected.

4.

If the heated seat switch is not turned off (“0”
on the thumbwheel), the seat will heat up to
the selected temperature level each time the
car is started.

NOTE:

Cooling the seat down takes considerably

longer than increasing its heat level.

Important Safety Belt Information

The use of safety belts helps to restrain you and
your passengers in case of a collision. In most states
and in Canada the law requires their use.

Safety belts provide best restraint when:

❑

the seatback is upright

❑

the occupant is sitting upright (not slouched)

❑

the lap belt is snug and low on the hips

❑

the shoulder belt is snug against the chest

❑

the knees are straight forward

To help you remember to fasten your safety belt, a
warning light may come on and a chime may
sound. See

Safety Belt Warning Light and Chime

in

the

Instrumentation

chapter.

See the following sections in this chapter for
directions on how to properly use these safety belts.
Also see

Safety Restraints for Children

in this

chapter for special instructions about using safety
belts for children.

File:06fnsst.ex

Update:Fri Jun 21 08:57:53 1996

«
...
126
127
128
129
130
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: Federal Signal Corporation Pages: 13

Brand: Camcar Pages: 6

Brand: iArmor Pages: 6

Brand: GATmatic Pages: 13

Brand: GMC Pages: 425

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: U & Me Brothers Pages: 6

Automotive 31006

Brand: KRAFTWERK Pages: 2

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: Brodit Pages: 2

Brand: Softride Pages: 4

Brand: Ford Pages: 458

Brand: Oldsmobile Pages: 380

Brand: Honda Pages: 569

1500 CLASSIC 2020

Brand: RAM Pages: 360

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands