Lincoln 1997 Town Car Owner'S Manual Download Page 134 | Manualshive

Page: 134 / 305

background image

130

WARNING

Position the shoulder belt height
adjuster so that the belt rests across the
middle of your shoulder. Be sure the
shoulder belt is properly positioned on
your shoulder each time you use the
belt. If the shoulder belt is off your
shoulder, on your upper arm or neck,
there is a greater risk of severe injury
in a collision.

Safety Belts for the Front Passenger

Outboard Seating Positions

Your vehicle is equipped with a dual locking mode
retractor on the shoulder belt portion of the
combination lap/shoulder safety belt for front seat
passengers and a locking “cinch tongue” for rear
outboard passengers.

Dual locking mode retractors operate in two
ways:

Vehicle sensitive (emergency) locking
mode

In this operating mode, the shoulder belt retractor
will allow the occupant freedom of movement,
locking tight only on hard braking, hard cornering
or impacts of approximately 5 mph (8 km/h) or
more. The retractor can also be made to lock by
pulling the belt out quickly.

Automatic locking mode

In this operating mode, the shoulder belt retractor
will be automatically locked and will remain locked
when the combination lap/shoulder safety belt is
buckled, and does not allow the occupant freedom
of movement. This mode provides the following:

❑

A tight lap/shoulder belt on the occupant.

❑

Child seat installation restraint.

File:06fnsst.ex

Update:Fri Jun 21 08:57:53 1996

«
...
132
133
134
135
136
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: Daihatsu Pages: 1718

ESCALADE FAMILY - SPECIFICATIONS 2011

Brand: Cadillac Pages: 1

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: Xblitz Pages: 30

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Brand: Radical Sportscars Pages: 44

Brand: Sagem Pages: 10

Portable Car Umbrella

Brand: Mynew Pages: 5

OPTIA hybrid 2020

Brand: Kia Pages: 54

Brand: Kargo Master Pages: 18

Follow me RAPID INTRACKER

Brand: Thule Pages: 8

Brand: Datsun Pages: 104

Brand: Volkswagen Pages: 188

Brand: Kargo Master Pages: 10

Brand: Ford Pages: 10

Brand: Fiat Pages: 204

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands