Lincoln 1997 Town Car Owner'S Manual Download Page 249 | Manualshive

Page: 249 / 305

background image

247

Ford strongly recommends the use of genuine Ford
replacement parts. If other than Ford or Motorcraft
parts or Ford authorized remanufactured parts are
used for maintenance replacements or for the
service of components affecting emission control,
such non-Ford parts should be equivalent to genuine
Ford Motor Company parts in performance and
durability. It is the owner’s responsibility to
determine the equivalency of such parts. Please
consult your warranty booklet for complete
warranty information.

WARNING

Do not park, idle, or drive your vehicle
in dry grass or other dry ground cover.
The emission system heats up the
engine compartment and exhaust
system, which can start a fire.

Watch for fluid leaks, strange odors, smoke, loss of
oil pressure, the charge warning light, the check
engine light, or the temperature warning light.

These sometimes indicate that the emission system
is not working properly.

Do not make any unauthorized changes to your
vehicle or engine. Changes that cause more
unburned fuel to reach the exhaust system can
increase the temperature of the engine or exhaust
system.

By law, anyone who manufactures, repairs, services,
sells, leases, trades vehicles, or supervises a fleet of
vehicles is not permitted to intentionally remove an
emission control device or prevent it from working.
In some of the United States and in Canada,
vehicle owners may be liable if their emission
control device is removed or is prevented from
working.

Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on for
more than five seconds after you shut it off or if it
misfires, surges, stalls, or backfires.

File:11fnmct.ex

Update:Mon Jun 17 13:54:56 1996

«
...
247
248
249
250
251
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Brand: Kargo Master Pages: 5

iBoard IB-ZK406

Brand: APS Auto Parts Specialist Pages: 3

Brand: BrandMotion Pages: 8

Brand: Trailboss Pages: 8

Brand: EUFAB Pages: 52

Vantage 12 Series

Brand: Ecco Pages: 5

MCL-7000 Series

Brand: Dakota Digital Pages: 2

Brand: Volvo Pages: 284

Brand: Gator Pages: 2

Brand: PAC Pages: 14

Brand: Kolpin Pages: 3

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: Saab Pages: 15

Brand: Mitsubishi Pages: 362

Brand: Scosche Pages: 8

Brand: Opel Pages: 44

Brand: Setma Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands