manualshive.com logo in svg

Lincoln 1997 Town Car, Owner'S Manual

The Lincoln 1997 Town Car Owner's Manual, the perfect companion for every proud owner, is available for download, absolutely free! This comprehensive manual provides all the necessary information and guidance to maximize your driving experience in the luxurious Lincoln 1997 Town Car. Download it now from manualshive.com!

Share
Download
background image

260

NOTE:

Rear axle lube quantities must be replaced

every 100,000 miles (160,000 km) or if the axle
has been submerged in water. Otherwise, the lube
should not be checked or changed unless a leak is
suspected or repair required.

Vehicle Storage

Maintenance Tips

If you plan on storing your vehicle for an extended
period of time (60 days or more), refer to the
following maintenance recommendations to ensure
your vehicle stays in good operating condition.

General

❑

Store all vehicles in a dry, ventilated place.

❑

Protect from sunlight, if possible.

❑

If vehicles are stored outside, they require
regular maintenance to protect against rust and
damage.

Body

❑

Wash vehicle thoroughly to remove dirt, grease,
oil, tar or mud from exterior surfaces, rear
wheel housing and underside of front fenders.

❑

Periodically wash vehicles stored in exposed
locations.

❑

Touch-up raw or primed metal to prevent rust.

❑

Cover chrome and stainless steel parts with a
thick coat of auto wax to prevent discoloration.
Re-wax as necessary when the vehicle is
washed.

❑

Lubricate all hood, door and trunk lid hinges
and latches with a light grade oil.

❑

Cover interior soft trim to prevent fading.

❑

Keep all rubber parts free from oil and solvents.

File:12fncst.ex

Update:Thu Jun 20 15:16:56 1996

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

Acdeos AXS FL Installation Instruction preview
AXS FL
Brand: Acdeos Pages: 7
Cadillac ESCALADE - BROCHURE 2009 Personalization Manual preview
ESCALADE - BROCHURE 2009
Brand: Cadillac Pages: 24
Cadillac Escalade Personalization Manual preview
Escalade
Brand: Cadillac Pages: 20
Cadillac Escalade 2016 Convenience/Personalization Manual preview
Escalade 2016
Brand: Cadillac Pages: 20
Vauxhall Cascada Quick Reference Manual preview
Cascada
Brand: Vauxhall Pages: 2
GATmatic TWC-562S Installation, Operation & Maintenance Manual preview
TWC-562S
Brand: GATmatic Pages: 13
Mobile Create MCM3 Instruction Manual preview
MCM3
Brand: Mobile Create Pages: 15
Mazda 2 2016 Owner'S Manual preview
2 2016
Brand: Mazda Pages: 720
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Brand: B-Speech Pages: 24
Whispbar K448W Fitting Instructions Manual preview
K448W
Brand: Whispbar Pages: 15
Webasto CC4E Installation And Service Instructions Manual preview
CC4E
Brand: Webasto Pages: 34
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Brand: Harman Kardon Pages: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Brand: TATA Motors Pages: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Brand: B&G electronics Pages: 7
Kuda 079020 Installation Instruction preview
079020
Brand: Kuda Pages: 2
Great Wall WEY VV5 Service Manual preview
WEY VV5
Brand: Great Wall Pages: 18
WIX WP9378 Installation Instruction preview
WP9378
Brand: WIX Pages: 2
Joie i-Level Instruction Manual preview
i-Level
Brand: Joie Pages: 53

Brands by name

Popular brands

Load more brands