Lincoln 1997 Town Car Owner'S Manual Download Page 77 | Manualshive

Page: 77 / 305

background image

73

Ashtray and Cupholder

Your vehicle has an ashtray/cupholder mounted to
the lower center of the instrument panel.

To open the ashtray, pull out the bottom edge of
the drawer until it stops.

To close, remove cup(s) and push drawer forward
until closed.

Power Point Electrical Outlet

The power point outlet is located under the
instrument panel to the right of the ashtray. This
outlet should be used in place of the cigarette
lighter for optional electrical accessories.

NOTE:

Do not plug optional electrical accessories

into the cigarette lighter. Electrical system damage
could occur.

To access the outlet, pull the cap off.

Ignition

Understanding the Positions of the

Ignition

The positions of the key in the ignition

ACC allows some of your vehicle’s electrical
accessories such as the radio and the windshield
wipers to operate while the engine is not running.

File:05fncft.ex

Update:Mon Jun 17 13:49:49 1996

«
...
75
76
77
78
79
...
»

Summary of Contents for 1997 Town Car


















































































































































































































































































































Reviews:

No comments

Related manuals for 1997 Town Car

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Brand: TrailFX Pages: 6

Brand: Subaru Pages: 99

Brand: Dodge Pages: 24

Brand: Prorack Pages: 20

Brand: UAZ Pages: 112

Brand: MVG Pages: 18

Brand: Oldsmobile Pages: 354

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

2011 RDX Navigation System

Brand: Acura Pages: 16

Brand: Stanley Pages: 6

Brand: Advent Pages: 8

Brand: Or-Fab Pages: 5

Brand: UCANDAS Pages: 4

Brand: Ford Pages: 46

Brand: Mont Blanc Pages: 10

Brand: Macally Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands